Filter :
Standard and/or project under the direct responsibility of ISO/TC 60/SC 2 Secretariat Stage ICS
Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors
95.99
Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors — Technical Corrigendum 1
95.99
Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors — Technical Corrigendum 2
95.99
Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors
95.99
Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors — Technical Corrigendum 1
95.99
Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors
60.60
Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting)
95.99
Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting) — Technical Corrigendum 1
95.99
Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting) — Technical Corrigendum 2
95.99
Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting)
95.99
Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting) — Technical Corrigendum 1
95.99
Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting)
60.60
Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength
95.99
Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength — Technical Corrigendum 1
95.99
Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength
95.99
Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength — Technical Corrigendum 1
95.99
Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength
60.60
Calculation of load capacity of spur and helical gears — Part 4: Calculation of tooth flank fracture load capacity
90.93
Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials
95.99
Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials
95.99
Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials
90.93
Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load
95.99
Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load — Technical Corrigendum 1
95.99
Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load
60.60
Calculation of load capacity of spur and helical gears — Part 20: Calculation of scuffing load capacity (also applicable to bevel and hypoid gears) — Flash temperature method
95.99
Calculation of load capacity of spur and helical gears — Part 20: Calculation of scuffing load capacity — Flash temperature method
60.60
Calculation of load capacity of spur and helical gears — Part 21: Calculation of scuffing load capacity (also applicable to bevel and hypoid gears) — Integral temperature method
95.99
Calculation of load capacity of spur and helical gears — Part 21: Calculation of scuffing load capacity — Integral temperature method
60.60
Calculation of load capacity of spur and helical gears — Part 22: Calculation of micropitting load capacity
90.93
Calculation of load capacity of spur and helical gears — Part 30: Calculation examples for the application of ISO 6336 parts 1,2,3,5
95.99
Calculation of load capacity of spur and helical gears — Part 30: Calculation examples for the application of ISO 6336 parts 1,2,3,5
60.60
Calculation of load capacity of spur and helical gears — Part 31: Calculation examples of micropitting load capacity
60.60
Calculation of load capacity of spur and helical gears — Application to marine gears
95.99
Calculation of load capacity of spur and helical gears — Application to high speed gears and gears of similar requirements
95.99
Calculation of load capacity of spur and helical gears — Application for industrial gears
90.93
Calculation of load capacity of bevel gears — Part 1: Introduction and general influence factors
95.99
Calculation of load capacity of bevel gears — Part 1: Introduction and general influence factors
95.99
Calculation of load capacity of bevel gears — Part 1: Introduction and general influence factors
60.60
Calculation of load capacity of bevel gears — Part 2: Calculation of surface durability (pitting)
95.99
Calculation of load capacity of bevel gears — Part 2: Calculation of surface durability (pitting)
95.99
Calculation of load capacity of bevel gears — Part 2: Calculation of surface durability (macropitting)
60.60
Calculation of load capacity of bevel gears — Part 3: Calculation of tooth root strength
95.99
Calculation of load capacity of bevel gears — Part 3: Calculation of tooth root strength
95.99
Calculation of load capacity of bevel gears — Part 3: Calculation of tooth root strength
60.60
Calculation of load capacity of bevel gears — Part 20: Calculation of scuffing load capacity — Flash temperature method
90.93
Calculation of load capacity of bevel gears — Part 30: ISO rating system for bevel and hypoid gears — Sample calculations
95.99
Calculation of load capacity of bevel gears — Part 30: ISO rating system for bevel and hypoid gears — Sample calculations
60.60
Calculation of load capacity of bevel gears — Part 32: ISO rating system for bevel and hypoid gears — Sample calculation for scuffing load capacity
60.60
Cylindrical gears — Calculation of service life under variable loads — Conditions for cylindrical gears according to ISO 6336
95.99
Petroleum and natural gas industries — High-speed special-purpose gear units
90.93
Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears — Part 1: Flash temperature method
95.99
Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears — Part 2: Integral temperature method
95.99
Gears — Surface temper etch inspection after grinding
95.99
Gears — Surface temper etch inspection after grinding, chemical method
95.99
Gears — Surface temper etch inspection after grinding, chemical method
90.93
Gears — Thermal capacity — Part 1: Rating gear drives with thermal equilibrium at 95 °C sump temperature
90.93
Gears — Thermal capacity — Part 2: Thermal load-carrying capacity
90.93
Gears — FZG test procedures — Part 1: FZG test method A/8,3/90 for relative scuffing load-carrying capacity of oils
95.99
Gears — FZG test procedures — Part 1: FZG test method A/8,3/90 for relative scuffing load-carrying capacity of oils
60.60
Gears — FZG test procedures — Part 2: FZG step load test A10/16, 6R/120 for relative scuffing load-carrying capacity of high EP oils
95.99
Gears — FZG test procedures — Part 2: FZG step load test A10/16, 6R/120 for relative scuffing load-carrying capacity of high EP oils
60.60
Gears — FZG test procedures — Part 3: FZG test method A/2, 8/50 for relative scuffing load-carrying capacity and wear characteristics of semifluid gear greases
95.99
Gears — FZG test procedures — Part 3: FZG test method A/2,8/50 for relative scuffing load-carrying capacity and wear characteristics of semifluid gear greases
60.60
Calculation of micropitting load capacity of cylindrical spur and helical gears — Part 1: Introduction and basic principles
95.99
Calculation of micropitting load capacity of cylindrical spur and helical gears — Part 1: Introduction and basic principles
95.99
Calculation of micropitting load capacity of cylindrical spur and helical gears — Part 2: Examples of calculation for micropitting
95.99
Lubrication of industrial gear drives
90.92
Lubrication of industrial gear drives
20.00
Design recommendations for bevel gears
60.60
Bevel and hypoid gear geometry — Part 1: Basic methods
40.20
Bevel and hypoid gear geometry — Part 2: Sample calculations
10.99
Bevel and hypoid gear geometry
95.99
Bevel and hypoid gear geometry
90.92

No matching records found. Please try changing the filter settings.